Archives of Acoustics, 45, 2, pp. 271–282, 2020
10.24425/aoa.2020.133148

Study of Effect of Linear Tip Relief Modification in Power Transmission Efficiency of Spur Gears

Narendiranath Babu THAMBA
School of Mechanical Engineering, Vellore Institute of Technology
India

Abhijeet Mukund TAMBARE
Vellore Institute of Technology
India

Krishna Caitanya ANANTHANARAYANAN
Vellore Institute of Technology
India

Rama Prabha DURAISWAMY
Vellore Institute of Technology
India

Shankar THANGAVELU
Vellore Institute of Technology
India

Raj Kumar EASWARA PILLAI
Vellore Institute of Technology
India

Ramalinga Viswanathan MANGALARAJA
University of Concepcion
Chile

This paper explores the influence of linear gear tip relief modification on power transmission efficiency. In real time applications gears experience transmission error (TE) during operation which increases noise and vibration and also results in increased tooth profile deformation during operation of the gear. By providing tip relief profile modification this TE can be decreased. Using MATLAB for computation and ANSYS for the simulation of deformation, stress, strain, life, and factor of safety results for the gear assemblies are obtained. Deformation results are used for the computation change in power transmission efficiency followed by the modal and harmonic analysis of the gears and gear assemblies to determine change in the first mode of natural frequency.
Keywords: linear gear tip relief profile modification; tooth profile deformation; transmission efficiency; transmission error (TE)
Full Text: PDF
Copyright © The Author(s). This is an open-access article distributed under the terms of the Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0).

References

Achchagam K. (2017), Design Data: Data Book of Engineerers, PSG College of Technology, India.

Banodiya B., Karma V.K. (2017), Measurement of transmission error in spur gears, International Research Journal of Engineering and Technology, 4(8): 2369–2375.

Beghini M., Bragallini G.M., Presicce F., Santus C. (2004), Influence of the linear tip relief modification in spur gears and experimental evidence, Proceedings of the 12th International Conference on Mechanics ICEM 12, Bari.

Beghini M., Presicce F., Santus C. (2006), Proposal for tip relief modification to reduce noise and sensitivity to meshing conditions in spur gears,Gear Technology, March/April: 34–40.

Gupta B., Choubey A., Varde G.V. (2012), Contact stress analysis of spur gear, International Journal of Engineering Research and Technology, 1(4): Article ID IJERTV1IS4052, 7 pages, https://www.ijert.org/research/contact-stress-analysis-of-spur-gear-IJERTV1-IS4052.pdf.

Faggioni M., Samani F.S., Bertacchi G., Pellicano F. (2011), Dynamic optimization of spur gears, Mechanism and Machine Theory, 46(4): 544–557, doi: 10.1016/j.mechmachtheory.2010.11.005.

Manurwar R.R., Hatwalane S., Agashe U.C. (2017), A review on optimum profile modification of spur gear, International Journal of Current Engineering and Technology, 7: 88–91, https://inpressco.com/wp-content/uploads/2017/05/Paper2088-91.pdf.

Markovic K., Vrcan Ž. (2016), Influence of tip relief profile modification on involute spur gear stress, Transactions of FAMENA, 40(2): 59–70, doi: 10.21278/TOF.40205.

Mei W., Na J., Yang F., Shen G., Chen J. (2016), The optimal design method and standardized mathematical model of tooth profile modification of spur gear, Mathematical Problems in Engineering, 2016, Article ID 6347987, 7 pages, doi: 10.1155/2016/6347987.

Niemann G., Winter H. (1983), Machine elements. Volume II: General gear, gear, basic principles, spur gear [in German: Machinenelemente Band II: Getriebe allgemain, Zahnradgetriebe, Grundlagen, Stirnradgetriebe], 2nd Ed., Springer-Verlag, Berlin Heidelberg.

Sankar S., Raj M.S., Nataraj M. (2010), Profile modification for increasing the tooth strength in spur gear using CAD, Engineering, 2(9): 740–749, doi: 10.4236/eng.2010.29096.

Tharmakulasingam R. (2009), Tranmission error in spur gear: static and dynamic finite element modeling and design optimization, PhD Thesis, School of Engineering and Design Brunel University, United Kingdom.

Tiwari S.K., Joshi U.K. (2012), Stress analysis of mating involute spur gear teeth, International Journal of Engineering Research and Technology (IJERT), 1(9): Article ID: IJERTV1IS9380, 12 pages, https://www.ijert.org/research/stress-analysis-of-matinginvolute-spur-gear-teeth-IJERTV1IS9380.pdf.




DOI: 10.24425/aoa.2020.133148